LinkTap guarantees the wireless valve controller and gateway products for 2 years from the date of purchase. The service life of lithium batteries is about twice that of alkaline batteries. Turn on the main valve on the pipe first, then press the blue Manual On/Off button on the ValveLinker to open the solenoid valve. Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- Save on Watering Timers & Controllers, Current slide {CURRENT_SLIDE} of {TOTAL_SLIDES}- You may also like, {"modules":["unloadOptimization","bandwidthDetection"],"unloadOptimization":{"browsers":{"Firefox":true,"Chrome":true}},"bandwidthDetection":{"url":"https://ir.ebaystatic.com/cr/v/c1/thirtysevens.jpg","maxViews":4,"imgSize":37,"expiry":300000,"timeout":250}}. If you already have a LinkTap system in the house, please start from Step 3 below. If the colors of the two wires are the same, it can be safely determined that the solenoid is not a DC latching type. As shown in the figure below, wire #1 needs to be connected to the flow meter working with solenoid valve #1, wire #2 needs to be connected to the flow meter working with solenoid valve #2, and so on. Do not use carbon-zinc batteries, NiMH or Ni-Cd rechargeable batteries. This product meets the applicable Industry Canada technical specifications.This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. Install the DC latching solenoid valve and optional flow meter on the PVC pipes, then connect the ValveLinker with the solenoid and flow meter using the supplied connection cables and waterproof connectors. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The ValveLinker comes with two connection cables: one is used to connect the ValveLinker and the solenoid valve, and the other is used to connect the ValveLinker and the flow meter. number of ValveLinkers & TapLinkers per Gateway: 15, Max. Operation is subject to the following two conditions: The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. Enable all fault alert options on the app. If you are in an area where the pipeline is at risk of freezing in the winter, you need to take proper measures to prevent the solenoid valve and the pipeline from being damaged in the winter. Tip: Placing the Gateway at a higher location will usually increase the wireless coverage. Please pay attention to the polarity of the wires when connecting the solenoid. Something went wrong. Be sure to tighten the two connectors to each other. A rule of thumb is that the two input wires of the DC latching solenoid are of different colors (for example, one red and one black). Power on the Gateway using the supplied USB cord and power adapter. When installing the flowmeter on the pipe, be careful not to let soil, dust, water, or other substances enter the waterproof connector of the flow meter. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If the actual flow rate is less than 2 liters/min, the flow meter may not detect the water flow, so the flow rate value on the app will be displayed as 0.If the preliminary watering test is ok, you can press the blue button on the ValveLinker again to close the solenoid valve. If the flow meter has been installed, the ValveLinker can detect the following faults in a real-time manner and then send push notifications and emails to you and your nominated person, e.g. Your email address will not be published. Before fixing the ValveLinker to a certain location, you can check the wireless receiving signal strength and connection performance of the device through the tool. (This tool can also be accessed in a web browser by visiting www.link-tap.com/health). Under warranty we will either replace the device or repair it free of charge if the following conditions apply: LinkTap has done its utmost to ensure that the fault detection & notification function works reliably. neighbor, friends, etc. The distance between the ValveLinker and the solenoid valve & the flow meter should not exceed the length of the connection cables. Determine the installation location of the ValveLinker. Press the Manual On/Off button on the ValveLinker, or activate Instant Watering on the app to start watering. Visit https://www.link-tap.com/app-manual or scan the QR code for the LinkTap app user manual. The positive wire (red) of the solenoid needs to be connected with the positive wire (red) of the connection cable, and the negative wire (black) of the solenoid needs to be connected with the negative wire (black) of the connection cable. Tip: The location of the ValveLinker and the Gateway has a great impact on the wireless performance of the devices. When the registration is completed, the Synced LED on the Gateway will turn solid green. Connect LinkTap Gateway to a LAN port of your home broadband modem (or a network switch, a router, a hub, a Wi-Fi extender) using the supplied ethernet cable. When a fault occurs, in order to avoid false positives, the system will make multiple measurements, so sending out real-time push notifications and emails will be delayed by 10 to 45 seconds. number of Gateways per user account: 6. To reduce possible interference, please place the Gateway over 30cm (or 1 foot) away from any power sockets and/or other electronic devices. A common way is to install a water drain valve or faucet on the pipe before the solenoid valve to drain the water from the pipe. You can also disable, partially enable or fully enable the Manual button lockout function through the app. Within 45 seconds, you should receive a water cut-off alert on your phone. For the 2-zone and 4-zone models, please pay attention to the serial number of the wire when connecting the flow meters. However, due to various factors in the real-world (e.g., network delay or interruption, equipment failure, battery quality problems, improper use of the device, etc. item 1 LinkTap G1S Wireless Water Timer & Gateway - Smart Sprinkler Timer with App, 4.9 out of 5 stars based on 13 product ratings, 4.8 out of 5 stars based on 58 product ratings, 4.9 out of 5 stars based on 121 product ratings, 4.7 out of 5 stars based on 168 product ratings, 5.0 out of 5 stars based on 3 product ratings, 4.5 out of 5 stars based on 2 product ratings, 4.9 out of 5 stars based on 58 product ratings. Operating water pressure range: 0.02-0.8MPa or 2.9-116 psi, Watering duration per cycle: 3 seconds to 23 hours 59 minutes Temperature of water flow: 1C to 40C, Flowmeter measurement range: 3 to 120 L/min with a measurement error of 5%, Wireless water timer power: two 9 volts alkaline, lithium, or rechargeable lithium batteries, Wireless transmission distance: up to 800m *, Max. on LINKTAP V1-4Z Wireless Watering System User Manual, Visit https://www.link-tap.com/app-manual, Shenzhen Wonderhuge Electronics WH-919 Active Noise Cancelling Headphones User Manual, Razor MX500 Dirt Rocket Adult & Teen Ride On High-Torque Electric Motocross Motorcycle Dirt Bik Instructions, Razor W13111701003 Electric Party Pop Electric Tekno Installation Guide, MALYAN MA20 FDM Belt 3D Printer User Manual, Suntech ST4345GPS Enabled LTE CAT-M1 AVL Device User Manual, KVIDIO WH201A Wireless Headphones User Manual, Gerni GPW-3600 240V High Pressure Washer Instruction Manual, enbrighten LED Wi-Fi Smart Caf Lights Instruction Manual, iRobot i3 / i4 Roomba Robot Vacuum Owners Manual, SHARP Digital Alarm Clock SPC276 User Manual. The ValveLinker comes with 3 models: 1-zone (V1-1Z), 2-zone (V1-2Z) and 4-zone (V1-4Z). This device must accept any interference, including interference that may cause undesired operation of the device. If possible, do not press the pipe clamp against the stainless-steel cover plate on the flow meter. The device damage due to incorrect or improper installation will not be covered by the warranty. The ValveLinker can only control the 9-24V DC latching solenoids; it can NOT drive any type of AC solenoids, nor can it drive semi-direct lift solenoid valves. Please read this user manual thoroughly before installing the LinkTap ValveLinker. Trending price is based on prices over last 90 days. This device meets the FCC and IC requirements for RF exposure in public or controlled environments. In some scenarios, you may need to move the Gateway closer to the ValveLinker via a Wi-Fi extender. It also works with the LinkTap 1-inch flow meter to measure flow rate and volume. If the flow meter has been installed, you can verify the water cut-off detection and notification process by following the steps below. In addition, if the device is placed below the ground, the LinkTap Gateway should be placed as high as possible (for example, upstairs). This device complies with Industry Canadas license-exempt RSS. As shown below, the device can be hanging on a wall, hanging or standing on a hardwood stake, or placed in a valve box. If the signal is weak, or the wireless connection performance is poor, then you need to adjust the location of the ValveLinker or Gateway to achieve a more stable wireless connection. This device complies with Part 15 of the FCC Rules. Add a new ValveLinker device through the LinkTap app. The real-time push notifications will be sent to all your smartphones and tablets with the LinkTap app installed, and an email will be sent to your registered email address and two other email addresses. Damage caused by frost is not covered by the warranty. 3 solid green LEDs (Power, Link and Internet) indicate that the Gateway has connected to the LinkTap cloud server. In addition, you can test the Instant watering function through the app. The LinkTap ValveLinker is a wireless valve controller for operating 9-24V DC latching solenoid valves. Use two 9V alkaline, lithium or rechargeable batteries (not included). After the ValveLinker has been connected to the solenoid valve and the flow meter, you can perform a preliminary watering test. The LinkTap app comes with aDevice Health Check tool. The water should pass through the solenoid valve and flow meter, and you can also see the real-time flow rate value on the app. The measurement range of the LinkTap 1-inch flow meter is 3-120 liters/min. LinkTap and its designated agents are not liable for any possible loss caused by false positives or false negatives. Press the blue Manual On/Off button once to start or stop watering. View cart for details. Comment document.getElementById("comment").setAttribute("id","a51fd0052465a5d3c1b987a2905f49d0");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. Actual ranges may vary depending on environmental conditions, building materials, etc. Wireless coverage claims are used only as a reference and are not guaranteed as each wireless network is unique. In order to extend the life of the valve and flow meter, it is strongly recommended to install an inline filter before the water enters the valve. In addition, be careful not to press the pipe clamp on the connection wire of the flow meter. Faults that occur as a result of incorrectly installed or leaking batteries or using third-party power adapter & USB cord are not covered by the warranty.
Sitemap 1