(video). In this way, you will get two protruding edges on the front of the door; these edges are necessary for the security of the mirror door itself. Extras and accessories: more overview more order! Thank you . It should not be confused with the base of a possible 50.2 cm wide linear module. An important piece of information about the custom-made cabinet with depth of 45 cm or less. Please open the packages in the order listed. Once the goods have been unloaded and received, their care is responsibility of the customer. In order for the motion sensor to work properly, it must always be positioned at the top. Continue by inserting the left side panel of the corner module. Attention: At the end of the assembly it is essential that the pre-holes, which will be used to fix the shelves, are located in the corner component on the right as shown in the photo and in the video. To assemble the corner module, please watch carefully the video at this link; below we repeat only a few fundamental points. With firm pressure and horizontally, just screw these screws into the dividing side panel. In the package, you will find also metal bars, which have to be placed and screwed on the edge of the door (one on the upper edge and the other on the lower edge). Drill slowly outwards on the pre-holes with a 3 mm wood drill and little pressure. stream (video), Unpack the back side of the wardrobe (C) and select the right one with the appropriate width for the respective module (the back side of the wardrobe is approx.1.5 cm wider than the module, as it is inserted into the milled groove in the cabinet side panels, base and top cover). endobj First screw the pins all the way in and then turn them back a little until the two holes are positioned vertically. Screw the supports for the shelves to the side panel of the bookcase. Then tighten the screw again. The shelf clicks into place and is thus firmly stabilized. Insert the back side of the wardrobe and the top cover into the milled groove and then slide the top cover to the left up to the left side of the cupboard until the pins enter the holes. endstream endobj 189 0 obj <>>> endobj 190 0 obj <>/ExtGState<>/Font<>/ProcSet[/PDF/Text]/Properties<>>>/XObject<>>>/Rotate 0/TrimBox[0.0 0.0 595.276 841.89]/Type/Page>> endobj 191 0 obj <>stream Now take care of the hinges for which there is no pre-drilled hole: Unscrew not much the vertical screws of the door hinges that still have to be mounted. (video), Put in the base and the left outer side panel together and tighten the screw shown below. In the case of a corner solution with 2 linear wardrobes (one with depth 45cm and the other one with depth 61cm): The 61 cm deep wardrobe stands directly against the corner wall. Pay attention to the correct positioning so that the pins can be inserted later (in the base and top cover of the wardrobe). Attention: The smallest corner base measures 49.6 cm (video). The enclosed wooden dowels are only used if you install two drawer modules one above the other. The hinges are simple to insert and must be attached to the doors using a hammer. (video), Fasten each clothes rail holder to the side panel with two screws on the side. In certain cases, instead, due to the reduction in depth and high height, it is mandatory to mount them on the wall. If you also ordered LED lights, please note the following before setting up: The horizontal sensor LED bar with motion detector (see video) is mounted under the wardrobe cover at the top (inside the cabinet). Then put the feet on and turn the module over again. Alternatively, you can use some double-sided tape. 05396590282, EUROMOEBEL NEWLINE GMBH VAT NUMBER:CHE-114.608.208 Letziweg 9, 4663 Aarburg. << /Length 9 0 R /Filter /FlateDecode /Type /XObject /Subtype /Form /FormType 1 /BBox [11 13 835 581] /Resources 10 0 R /Group << /S /Transparency /CS /DeviceCMYK Close the doors of the wardrobe, then switch off and on the general electric panel of the house, so that the sensors work correctly, when you open the doors. Wardrobe Made to Measure, Fitted Wardrobe and Roof Pitched cabinet, Assembly instructions and videos of the wardrobes, Video Montage Freestanding Wardrobe / Fitted Wardrobe, Video Montage Wardrobe with sliding doors and integrated TV, Assembly and installation videos Accessories, Assembly of the trouser hanger (pull-out) / belt / tie extension, Handle K panel handle, entire door length assembly, Fixing the cabinet doors when missing hinge holes, IDAW installation of the fitted wardrobe side panels, Fitted wardrobe: building instructions feet of the last side wall, Videos Wardrobe, Chest of drawers and Accessories, Installation of the vertical LED bar (in the dividing side panel), Assembly instructions: Freestanding wardrobe, IDAW s.r.l. Since the same LED lengths are used for different cupboard heights, it can happen that a small part of the lower, vertical LED bar is covered by the wardrobe base. Place the top on the top cover of the sideboard and screw it with self-tapping screws (35 mm long). Screw from underneath the top cover of the sideboard, until you reach the top. 2)This step must be done in two people with the utmost attention and safety! For safety and practical reasons, please note the following: To avoid damage to the material and accidents, the cabinet should be assembled by two people. Use the two supplied screws for this. Now connect the side panel of the bookcase to the wardrobe outer side panel (attention: for this step, you need someone to hold the other side of the top up). The hinges are simple to insert and must be attached to the doors using a hammer. Finally slide the top in and screw it to the already mounted top. This is useful for stabilizing the top and the angle, since no pins are used. Then tighten the screws again. If there is space above the top, fix the bookcase to the wardrobe from above with metal angles. - C.F. hVYo8+|LP. The person who performed the installation must attach it to the wall before installing the door to avoid the risk of falling forward. Attention: these screws are not supplied). If the top of the bookcase is less than 3cm from the ceiling: This will help you to avoid assembly difficulties! /Rotate 0 >> Unpack the base (F) and the top cover (E). Now mount the other side panel of the bookcase as well. Depending on the colour of your closet, you will receive a bottle or a can of paint. With a straight plate junction with 4 holes fix the top with the angle. Carry out this step both in the base and the top cover. Insert the corner into the base and fix it with the pins and dowels. 5 0 obj Repeat the same procedure for the other side panel. << /Length 6 0 R /Filter /FlateDecode >> (video). Assemble all accessories firstly (when one door of the wardrobe is already assembly). Unpack the shelves, the base and the top of the bookcase. Please proceed precisely to ensure that they can be connected easily later. Now assemble the corner as shown in the video: Use the Hex (Allen) key (included) and a spirit level to position the wardrobe horizontally. Unpack the outer side panel of the wardrobe. For the other door of this module, hinges with 180 opening are provided (please note: they are not delivered already assembled). Be careful with the next step! This leaves a small gap between the cover shelf and the top drawer. See also our montage film. q ouo/T\. Screw the four pins into the indicated holes. &{iHg` ` ` Horizontal LED strips: For the power cable, a hole should be drilled into the wardrobe top cover on the left outside the position where the LED bar is to be screwed on, so that the power cable can be routed above and behind the wardrobe to a socket. The shelf can also just be put on if you prefer. Insert the various elements. Now unpack the first door in the appropriate width. IMPORTANT: Glue ordinary furniture felts (not included) to the bottom of the leveling feet to avoid the wardrobe from scratching the floor when it is moved. Attention: Mount the handle precisely and straight! The drawer module for installation inside the wardrobe is almost completely assembled. Attention: if you have also ordered a side bookcase, read point 20 right now (for the assembly of the bookcase and of the wardrobe outer side panel, on which the bookcase will stand). The third variant for the free standing wardrobe as for fitted wardrobe is to accommodate the transformer on the top of the cabinet cover: However, this is only possible if, in addition to the necessary centimetre that is required for the construction, there is about 2 cm more space up to the ceiling. Please proceed precisely to ensure that they can be connected easily later. Then position the element inside the wardrobe: either place the drawer module on the cupboard floor or mount it at a higher point: To place it further up, place it on a shelf. In this wardrobe, the door of the last module (with normal hinges and without handles) will not be usable. Assembly instructions: Freestanding cabinet, Please take the time to read the instructions. If you have more than 2,5 cm space between the top and the ceiling, proceed as follows: Insert the back panel first, then slide the longest top in and raise it as much as needed to hook it onto the pins and the wooden pins. %%EOF Once you have assembled the whole wardrobe, reset the LED lights, while the doors are closed. In our video you can see how to assembly it with the wardrobe dividing side panel hole already prepared; however, it is much easier to install on a cupboard dividing side lying on the floor or on the table. << /Type /Page /Parent 4 0 R /Resources 7 0 R /Contents 5 0 R /MediaBox [0 0 841.89 595.276] If not, please continue on with point 11! With the help of a ruler, mark the points where the feet will be fixed; help yourself by referring to the base (or to the top as in the video). 8 0 obj hb```f``e`e`hdb@ !$..u,n6kL SxEOM/Y kk,:Hy[|L',8g;MNBfa>q_UH%X]yZ3SD?k, CGGGG D1@[ZD"KK2*` FO0m EX ~f7|/93&Yg^ b oe04hkK [Y7#$A\|(|@ +x This step concerns only the assembly of a sideboard. If you have 1 cm of space between the hat and the ceiling, proceed as follows: First insert the back panel, then slide the longest top in and hook it only to the wooden pins (without using the metal pins). Attention: If the cover cannot be pushed in, check whether both the holes and the pins are correctly positioned as described above. For this, the milled groove on the edge must be opened. If there are no holes for the leveling feet: (video). Install the screw covers: place them on the larger holes so that they are covered. (video) The last option is to cut a cutout for the transformer in the wardrobe back: This has the advantage that it is easily accessible. In case of mirror doors: << /ProcSet [ /PDF ] /XObject << /Fm1 8 0 R >> >> Continue by inserting the left side panel of the corner module. Do not tighten the screws immediately one after the other, but screw them in step by step, i.e. Use a screwdriver to open the milled groove, into which the back side of the wardrobe will later be inserted, up to the edge (see drawing below). Attention: As long as the left side panel of the corner module is not mounted, the top is movable; therefore pay particular attention during this step. Put in the side panel of the bookcase and the wardrobe outer side panel together and tighten the screws. If necessary, assembly the handles (the handles are already milled in the integrated door variant). 6 0 obj In any case, you have to begin with the assembly of the outer side panel, which will not stand behind the bookcase. Then, insert the other side panel of the bookcase and hook the top from underneath. Before proceeding with the installation, it will be the customers duty to collect all useful information for assembly using the videos and assembly instructions provided by IDAW. 188 0 obj <> endobj The vertical LED bar, in the dividing side panel (see video), is installed in the inner cheek in which the milling is provided for this at the factory. IDAW cannot be held responsible for damages deriving from improper use or modifications made to the product. % Loosen screws A slightly to raise or lower the respective door. A second person should check that the drilling is being carried out perfectly in horizontally to the door. Screw the four pins (see photo below) into the indicated holes. (video). First attach the leveling feet (see the photo) to the first left outer side panel only on the side facing the inside of the wardrobe (i.e. Any unauthorized modification made to the wardrobe structure and its components or any improper use of the product will automatically void the product warranty as our cabinets must be installed following the instructions provided and respecting their normal working and use. Now insert and tighten the screws. The package includes a longer screw as well. If necessary first remove the cover and correct the position of the holes and pins. 3 0 obj Continue with the assembly of the other parts of the module. After the drawer element has been positioned in the cabinet, first place the closing strips on the left and right on the wooden pins provided and tap them into place (Attention: in the photos, the strips were installed outside the wardrobe, which you should do better rather than inside the wardrobe). 2 cm forward. In order to assemble this wardrobe, you can start with the corner module, and then continue with the other linear modules on the sides of the corner. 2) Use the double-sided tape to first attach the mirror to the door. Pay attention to the correct position of the pins and the holes. The easiest way to accommodate the narrow transformer is behind the dividing side panel if there is at least 3 cm of space between one of the wardrobe dividing side panel and wall behind the side cover panel (when you have ordered fitted wardrobe). (video). 4) Finally, cover the screws with the screw covers provided. Then mount the handle with the supplied screws. Then, connect the outer side panel to the structure of the wardrobe, and screw. %PDF-1.4 % In the second case, the brush is not included. Uninominale - UST. When opening the package of metal parts, small parts and fittings, please ensure that no part is lost, since the parts are counted exactly and are only available in the number required for assembly. ( -?U1seP;dL188Cb-V~6}ww{wq~?-6n6rX~%vo{o_{K?o %PDF-1.3 Then, insert the metal components into the holes on the innerside of the side panel and the wooden pins along the edge of the panel. Attention, these are not identical! - Company subjected to the activity of management and coordination of IDAW s.r.l. 3) Attach the mirror to the door by tightening the security screws with a screwdriver (not an electric screwdriver to avoid breaking the mirror). IdNr. (Video Side Bookcase Assembly). It will therefore be necessary to use all the necessary personal protective equipment in order to guarantee a safe assembly. The shelves are mounted with the screws shown in the photo. Screw th four pins i the holes on the lacquered side as well. The drawer module is not attached separately, but is stable due to its weight and usually standing behind the door hinges. endstream Place the longest part of the corner base on the ground. Insert the smaller base and screw it to the larger base; then insert the back panel. Usually, our closet does not need to be wall-mounted as it is quite heavy and stable. xruy":^C\l`(U We also remind you that during the installation phase all the regulations in force for the respective countries in terms of safety must be respected. To determine the position of the hinges, one of the doors was already installed. : IT 05173760280, Montefiori s.r.l. Furthermore, IDAW cannot be held responsible for any damage caused after delivery or during assembly.

Sitemap 0